0

Your Cart is Empty

Sold out

Denafrips Terminator Plus DAC

1.The TERMINATOR-PLUS DAC is built upon the success of the TERMINATOR DAC. DENAFRIPS push the boundaries further in all aspects, to reach the new heights.



2.SOPHISTICATED DESIGN, DIGITAL/ANALOGUE ISOLATION
The TERMINATOR-PLUS Digital Processing Board and R-2R ladder network arrays are completely isolated. The two boards are physically linked by the OCXO module. The physical isolation yields even lowered noise-floor and achieved higher signal to noise ratio.
OVEN-CONTROLLED CRYSTAL OSCILLATORS – OCXO
The BEST clocks are the clocks inside the DAC.

The TERMINATOR-PLUS is equipped with dual OCXO operating at audio frequencies 45.1584Mhz, 49.152Mhz. Encapsulated in a metal casing, located at the center of the DAC, these OCXO are specially designed for high-end audio applications with ultra-low phase-noise and ultra-accuracy. The dual OCXO are powered by the complete redesigned power supply circuitry (encapsulated, shielded, underneath the main boards), supplying constant current to the OCXO. The adequate power reserves ensure linearity and stability of the OCXO.

ADAPTIVE FIFO BUFFER RECLOCKING
The DENAFRIPS approach to address the jitters issue by the FIFO BUFFER RECLOCKING. The adaptive FIFO buffer store the digital audio data in the memory. These data are read from the memory using the ultra-low phase noise, ultra-accuracy OCXO, located right in the DAC.
The data bits are converted to analogue signal by the true balanced R-2R ladder network arrays. The linearity of the conversion is guaranteed by the high-precision thin film resistors, with low thermal effect temperature coefficient of the low 10/15ppm.



3.MASTER CLOCK ECO-SYSTEM
With the GAIA and AVATAR matching clock input, the digital front-end can now be synchronized with the CLOCK-OUT feature of the Terminator-Plus DAC. 

Technical Highlights:
Proprietary R2R + DSD Architecture
True balanced 26BIT R2R + 6BIT DSD (32 steps FIR Filters)
Matched Precision Thin Film 0.005% R-2R Network Arrays           
Encapsulated Flagship Ultra Low Noise Power Supply
High-end Oven Controlled Crystals OCXO
Adaptive FIFO Buffer Reclocking
New Improved Digital Signal Processing FPGA Code
DSD1024, PCM1536 Supports On USB & I²S Input
Proprietary USB Audio Solution via STM32F446 Advanced AMR Based MCU
Licensed Thesycon USB Driver For Windows Platform
Driverless On Mac & Linux
Dual AES/EBU Input Supports
Sharp/Slow Filters Option
I²S Pinout Configuration
I²S DSD Channel Swap Configuration
           
DSD:
DSD64-DoP On All Input
DSD1024 On USB & I²S Input Only

PCM:
24bits / 44.1, 48, 88.2, 96, 176.4, 192KHz On All Input
1536kHz On USB & I²S Input 
 
Sampling Mode: Non-Oversampling NOS / Oversampling OS
         
Digital Input:
Coax via RCA
TOSLink x 1
AES/EBU x 2
USB
I²S via HDMI LVDS
I²S via RJ45 LVDS
I²S via RJ45 LVCMOS

Analog Output:          
RCA at 2.0Vrms, 625 Ω
XLR at 4.0Vrms, 1250 Ω
 
Clock Output:          
44.1KHz, 48KHz
22.5774Mhz, 24.576Mhz
45.1548MHz, 49.152Mhz
 
Frequency Response: 20-40KHz -0.2dB
THD+N: 0.0010%
S/N Ratio: 127dB
Dynamic Range: >132dB
Stereo Crosstalk: -110dB

AC Power Requirement: 100-240VAC, 50/60Hz (Worldwide Voltage)
Power Consumption: ≤20W
Dimension: 430 x 380 x 105 mm
Package Dim: 610 x 570 x 275 mm
Package Content: DAC only. No power cord & remote control.
Weight: 19.0 Kg           
Color: Silver / Black